Brief Introduction of Functions

Based on high performance microprocessor technology, supporting standard DMX512 protocol, this controller is available for cross-platform operation on DMX console or DMX simulation software (our DMX Controllers support most DMX consoles and DMX simulation software, A TEST-OPERATION IS HIGHLY RECOMMENDED.) With this enhanced tool, you can manage and design color changing patterns and changing speeds from across platforms.

Functions

With over 30 preprogrammed color changing patterns, including gradual changing, screening and jumping, our DMX controller offers a variety of display options.. As a powerful color managing controller, it will enable you to choose the desired pattern and appropriate speed to manage your RGB LED lighting fixtures.

With 0 to 100 dimming grades, you can also control the color and brightness according to your requirements easily, and mix up to 1 million different colors.

The LCD monitor on the controller offers an easy and visible managing method; the mounting bracket will enable the operator to easily fix the controller onto any place.

Wiring Diagrams

1. LED Strips

2. LED Modules

Function Introduction

1. Physical Specifications
Dimension: L190 x W120 x H50 mm
Weight: 830g
Working Environment: dry environment
Buttons: MODE, SETUP, UP & DOWN
Data Interfaces: DMX512

2. Electrical Specifications
Input Voltage: 12VDC or 24VDC
Output Load Current: 10A per line, 3 lines
Output Power: 720W (24VDC), 360W (12VDC)
Operation Temperature: -10℃~50℃ (14℉~122℉)

3. Function of Buttons
MODE: Select the preferred pre-programmed color pattern.
SETUP: Set the parameters of selected color pattern.
UP: Increase the parameter step by step
DOWN: Decrease the parameter step by step

4. Button "MODE" Introduction

5. Button "SETUP" Introduction
MODE 1-8 is static color without setup function.

6. How to set the DMX controller under DMX512 mode?
Under DMX512 mode, the DMX controller occupies 2 channels/addresses. The first channel/address is for mode selection; the second channel/address is for speed selection.
Please follow the below steps to set up your DMX controller:

1. Set DMX controller to DMX512 MODE;
2. Set DMX channel/address for the DMX controller: if the DMX channel/address is set to 13, the controller will occupy channel/address 13 & 14; if the DMX channel/address is set to 128, the controller will occupy channel/address 128 & 129;
3. Manage the first channel/address on the DMX console, like 13 or 128, to select the preferred pattern to use;
4. Manage the second channel/address on the DMX console, like 14 or 129, to set the changing speed.
   

7. How to set the DMX controller under DMX512 DECODER mode?
Under DMX512 DECODER mode, the DMX controller occupies 3 channels/addresses. The first channel/address is for adjusting brightness of red color; the second channel/address is for adjusting brightness of green color; the third channel/address is for adjusting brightness of blue color.

1. Set DMX controller to DMX512 DECODER mode;
2. Set DMX channel/address for the DMX controller: if the DMX channel/address is set to 13, the controller will occupy channel/address 13, 14 & 15; if the DMX channel/address is set to 128, the controller will occupy channel/address 128, 129 & 130;
3. Manage the first channel/address on the DMX console, like 13 or 128, to adjust the brightness of red color;
4. Manage the second channel/address on the DMX console, like 14 or 129, to adjust the brightness of green color;
5. Manage the third channel/address on the DMX console, like 15 or 130, to adjust the brightness of blue color.

Precautions

1. Avoid installing this controller during times of lightning, or in areas that have intense magnetic or high-voltage fields.

2. The controller should be installed indoors. Otherwise, please arrange rain sheilding.

3. Make sure the wires are connected correctly, and avoid short cuts that may burn out the fuse.